California has issued a Warning for all aluminum products see – CA Prop 65
-
Twin injectors are for use specifically with our Shooting Star systems. The different ratios give varying balances of lamination All injectors are built to work with the 5/8th Industry Standard injection Sprue. -
This O-Ring Kit will provide you with all O-Rings needed for our Twin Injectors. Simply pick the injector type (1:1 Twin, 3:1 Twin, Swirl, 4 oz Single, 8 oz Single ) that you need replacements for from the drop-down menu. You now can also choose between the Quad O-Ring and Round O-Ring for your pistons. -
27 legs extend from the center ball to an outer diameter of 2.5 inches. Legs have a slight taper to enhance their action. Primarily designed for catching smallmouth and largemouth bass when using forward-facing sonar. -
Ideal for keeping single or twin injectors warm, when you are producing a run of bait. Ideal if you are switching between colors and using multiple injectors, or if it is cold and you simply need to keep it hot between shots. Compatible with either our twin or single injectors. A must-have for any work station. -
The injectors have a quick release locking pin for the tip Our Medium injector holds 4oz Our Large injector holds 8oz -
This Thermal Injector Sleeve helps keep the plastic warm inside your injector. Please note-This is the cost of the Thermal Injector Sleeve only!! Not including the injector!! -
These coil pins sit in the injection port under the brass disk. It is a guide to know when to stop turning your injector to the 'open' or 'closed' position in the Shooting Star and Mini Shooting Star. -
Out of stock
DUE TO A SUPPLY ISSUE, WE ARE NOT ABLE TO TAKE YOUR ORDER ONLINE. LEAD TIME IS CURRENTLY 2 MONTHS OUT. PLEASE CONTACT OUR OFFICE AT OR CALL 318-255-7144 AND ASK FOR CHERIE FOR MORE INFORMATION.
These systems are CUSTOM BUILT and only have a few available at a time. If it is sold out please sign up on our wait list and you will be contacted shortly.
This system is NOT designed to cook plastisol...it is designed to hold it at a set temperature while you are shooting your molds. Cooking plastisol in this system WILL void the warranty.
PLEASE NOTE!!! THE SHIPPING CHARGED DURING CHECKOUT IS NOT CORRECT. YOU WILL BE CONTACTED WITH THE REMAINING SHIPPING BALANCE AFTER YOU HAVE PLACED YOUR ORDER. IF YOU WOULD LIKE TO CHECK YOUR SHIPPING AMOUNT BEFORE ORDERING PLEASE EMAIL US AT .
Telephone: 1-318-255-7144
The pots and manifold are solid aluminum, for maximum heat transfer. All parts are CNC machined in-house.
Features:
Ports on each pot for single color use
Center manifold/port for two-color injection/lamination
Pocket in the manifold for heating injector
Pot lids have a view-port and hold the stirrer motor in position
Stirrer motors are VARIABLE speed with a maximum speed of 75 rpm
Both pots have a ceramic insulating blanket with a protective aluminum wrap
The system is mounted to an aluminum base plate, with "U" brackets at each port for locking injectors in position while drawing plastic
A control box is mounted under the base plate: there are 2 rear power cords. Temperature controllers, motor speed controllers, and switches are mounted in the front panel, stirrer motors plug into the side panels. A ventilation fan and louvers in the side panels maintain an airflow across the controls and relays
Specification:
115 VAC
20 AMPS
2 x 1000 watt heaters (8.7 amps each)
Motors/Controls (0.5 amps each)
Pot capacity 2 x 96 fluid ozs. (6 quarts total)
1:1 Twin Injector included 8 oz (2 x 4 oz barrels)
Temperature controllers are digital, with Fahrenheit readout and temperature sensors. Temperature is maintained to within +/- 4 deg, although this can be adjusted through the controller
NOTE:
The cost of shipping with full insurance via UPS will be charged at a discounted rate.
Due to the custom nature of these machines, please allow three to four weeks from the time of order to shipping. -
Three (3) White O-Ring's for the brass ports on the front of the Mini and Regular (Large) Shooting Star Injection System.
