California has issued a Warning for all aluminum products see – CA Prop 65
-
The injectors have a quick release locking pin for the tip Our Medium injector holds 4oz Our Large injector holds 8oz -
This O-Ring Kit will provide you with all O-Rings needed for our Twin Injectors. Simply pick the injector type (1:1 Twin, 3:1 Twin, 4 oz Single, 8 oz Single ) that you need replacements for from the drop-down menu. -
These systems are CUSTOM BUILT and only have a few available at a time. If it is sold out please sign up on our wait list and you will be contacted shortly.
PLEASE NOTE!!! THE SHIPPING CHARGED DURING CHECKOUT IS NOT CORRECT. YOU WILL BE CONTACTED WITH THE REMAINING SHIPPING BALANCE AFTER YOU HAVE PLACED YOUR ORDER. IF YOU WOULD LIKE TO CHECK YOUR SHIPPING AMOUNT BEFORE ORDERING PLEASE EMAIL US AT .
Telephone: 1-318-255-7144
The pots and manifold are solid aluminum, for maximum heat transfer. All parts are CNC machined in-house. Features: Ports on each pot for single color use Center manifold/port for two-color injection/lamination Pocket in the manifold for heating injector Pot lids have a view-port and hold the stirrer motor in position Stirrer motors are VARIABLE speed with a maximum speed of 75 rpm Both pots have a ceramic insulating blanket with a protective aluminum wrap The system is mounted to an aluminum base plate, with "U" brackets at each port for locking injectors in position while drawing plastic A control box is mounted under the base plate: there is a single rear power cord. Temperature controllers, motor speed controllers, and switches are mounted in the front panel, stirrer motors plug into the side panels. A ventilation fan and louvers in the side panels maintain an airflow across the controls and relays Specification: 115 VAC 20 AMPS 2 x 1000 watt heaters (8.7 amps each) Motors/Controls (0.5 amps each) Pot capacity 2 x 96 fluid ozs. (6 quarts total) 1:1 Twin Injector included 8 oz (2 x 4 oz barrels) Temperature controllers are digital, with Fahrenheit readout and temperature sensors. Temperature is maintained to within +/- 4 deg, although this can be adjusted through the controller NOTE: The cost of shipping with full insurance via UPS will be charged at a discounted rate. Due to the custom nature of these machines, please allow two to three weeks from the time of order to shipping. -
These systems are CUSTOM BUILT and only have a few available at a time. If it is sold out please sign up on our wait list and you will be contacted shortly.
PLEASE NOTE!!! THE SHIPPING CHARGED DURING CHECKOUT IS NOT CORRECT. YOU WILL BE CONTACTED WITH THE REMAINING SHIPPING BALANCE AFTER YOU HAVE PLACED YOUR ORDER. IF YOU WOULD LIKE TO CHECK YOUR SHIPPING AMOUNT BEFORE ORDERING PLEASE EMAIL US AT .
Telephone: 1-318-255-7144
Ports and manifold are solid aluminum, for maximum heat transfer, ALL parts are CNC machined in house Center Manifold/Port for two-color injection Pocket in the manifold for heating injectors Ports for single color injection on both pots Pot lids have a viewport and hold the stirrer motors in a position Stirrer motors are VARIABLE speed with a maximum of 75 rpm Pots have a ceramic blanket for insulation and a protective aluminum wrap The system is mounted to an aluminum base plate, with U brackets at each port for locking the injectors in place while drawing plastic A control box is mounted under the base plate; there is a single rear power cord. Temperature controllers, motor speed controls, and switches are mounted in the front panel, stirrer motors plug into the side panels. A ventilation fan and louvers in the side panel cool the controls and relays Specs 115 VAC 2 x 20 amps circuits 2 x 2000 watt heaters (17.4 amps each) Motors/controllers 0.5 amps Pot capacity 8 quarts or 256 oz PER POT Temperature controllers are digital with a Fahrenheit readout and a sensor. Temperature is maintained to +/- 4 deg 1:1 Twin Injector 8 oz (2 x 4 oz barrels) 1 Pair of Hot Mill Gloves NOTE: The cost of shipping with full insurance via UPS will be charged at a discounted rate. Due to the custom nature of these machines, please allow two to three weeks from the time of order to shipping. -
This Thermal Injector Sleeve helps keep the plastic warm inside your injector. Please note-This is the cost of the Thermal Injector Sleeve only!! Not including the injector!! -
A direct replacement for damaged or worn-out twin injector nozzles. Includes all replacement O rings you will need for rebuilding. -
Twin injectors are for use specifically with our Shooting Star systems. The different ratios give varying balances of lamination All injectors are built to work with the 5/8th Industry Standard injection Sprue.
